CUSTOM BUILDING PRODUCTS INC -- 2010, PREMIXED STUCCO PATCH  -- 8010-00N027795
<pre>=====================  Product Identification  =====================

Product ID:2010, PREMIXED STUCCO PATCH
MSDS Date:05/04/1987
FSC:8010
NIIN:00N027795
=== Responsible Party ===
Company Name:CUSTOM BUILDING PRODUCTS INC
Address:5511 SALT LAKE AVE
City:BELL
State:CA
ZIP:90201
Country:US
Info Phone Num:213-582-0346
Emergency Phone Num:213-582-0346
Preparer's Name:LORI JAMESON
CAGE:CUSTO
=== Contractor Identification ===
Company Name:CUSTOM BUILDING PRODUCTS
Address:6511 SALT LAKE AVE.
City:BELL
State:CA
ZIP:90201
Country:US
Phone:213-582-0846
CAGE:CUSTO

=============  Composition/Information on Ingredients  =============

Ingred Name:CALCIUM CARBONATE (LIMESTONE)
CAS:1317-65-3
RTECS #:EV9580000
Fraction by Wt: 50%
OSHA PEL:15 MG/M3 TDUST
ACGIH TLV:10 MG/M3 TDUST

Ingred Name:SILICA, CRYSTALLINE - QUARTZ; (SILICON DIOXIDE)
CAS:14808-60-7
RTECS #:VV7330000
Fraction by Wt: 30%
OSHA PEL:SEE TABLE Z3
ACGIH TLV:0.1 MG/M3 RDUST;9293

Ingred Name:STODDARD SOLVENT; (ALIPHATIC HYDROCARBON)
CAS:8052-41-3
RTECS #:WJ8925000
Fraction by Wt: <5%
OSHA PEL:500 PPM
ACGIH TLV:100 PPM; 9293

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES  Skin:NO  Ingestion:YES
Reports of Carcinogenicity:NTP:NO    IARC:YES	 OSHA:NO
Health Hazards Acute and Chronic:THIS PRODUCT CONTAINS 1 OR MORE
    CHEMICALS KNOWN TO STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH
    DEFECTS OR OTHER REPRODUCTIVE HARM. INHAL:EXCESSIVE INHALATION OF
    VAPORS MAY CAUSE NASAL IRRITATION AND HE ADACHE. SKIN:PROLONGED
    CONTACT MAY CAUSE MODERATE IRRITATION. EYES:CAN CAUSE IRRITATION,
    REDNESS, (EFTS OF OVEREXPOS)
Explanation of Carcinogenicity:CARYSTALLINE SILICA:IARC -GROUP 2A.
Effects of Overexposure:HLTH HAZ:AND BLURRED VISION. INGEST:MAY CAUSE
    GASTROINTESTIONAL IRRITATION.
Medical Cond Aggravated by Exposure:PREEXISTING SKIN DISORDERS AND
    RESPIRATORY DISEASE.

=======================  First Aid Measures  =======================

First Aid:EYE:IMMEDIATELY FLUSH WITH WATER FOR AT LEAST 15 MINUTES.
    SEEK MD ATTENTION IF IRRITATION PERSISTS. SKIN:WASH AREA WITH SOAP
    AND WATER. SEEK MD ATTENTION IF IRRITATION RESULTS. INHAL:IF
    AFFECTED, REMO VE PERSON TO FRESH AIR. INGEST:INDUCE VOMITING. SEEK
    IMMEDIATE MD ADVICE AND/OR ATTENTION.

=====================  Fire Fighting Measures  =====================

Flash Point:NONE
Lower Limits:1.0%
Extinguishing Media:FOAM, CARBON DIOXIDE, DRY CHEMICAL.
Fire Fighting Procedures:NONE. USE NIOSH/MSHA APPROVED SCBA AND FULL
    PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:MATERIAL CAN SPLATTER ABOVE 212F (100C).
    DRIED FILM CAN BURN.

==================  Accidental Release Measures  ==================

Spill Release Procedures:SPILLED MATERIAL MAY BE REMOVED WITH A SHOVEL
    AND INERT ABSORBENT.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

======================	Handling and Storage  ======================

Handling and Storage Precautions:STORE AWAY FROM HEAT SOURCES.
Other Precautions:NONE

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:IF EXPOSURE MAY EXCEED TLV RANGE, USE NIOSH/MSHA
    APPROVED RESPIRATOR TO PREVENT OVEREXPOSURE.
Ventilation:GENERAL MECHANICAL VENTILATION SHOULD BE SUFFICIENT.
Protective Gloves:PLASTIC OR RUBBER GLOVES.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:ADEQUATE CLOTHING SHOULD BE WORN TO PREVENT
    FROM CONTACTING SKIN.
Work Hygienic Practices:GOOD HOUSEKEEPING PROCEDURES SHOULD BE
    OBSERVED.
Supplemental Safety and Health
NONE SPECIFIED BY MANUFACTURER.

==================  Physical/Chemical Properties  ==================

HCC:N1
Boiling Pt:B.P. Text:212F,100C
Vapor Density:HVR/AIR
Spec Gravity:1.9 (H2O = 1)
Evaporation Rate &amp; Reference:SLOWER THAN ETHER
Solubility in Water:MISCIBLE
Appearance and Odor:WHITE, SANDY PASTE WITH SLIGHT SOLVENT ODOR.

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
AVOID STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:NONE KNOWN
Hazardous Decomposition Products:THERMAL DECOMPOSITION IN PRESENCE OF
    AIR MAY YIELD CO AND/OR CO2.

====================  Disposal Considerations  ====================

Waste Disposal Methods:DISPOSE OF PRODUCT IN ACCORDANCE WITH LOCAL,
    STATE AND FEDERAL REGULATIONS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.